|
Posted by Gunner on March 20, 2006, 12:44 am
Please log in for more thread options
One of the things I brought home this weekend..was a Mod 530 Hotsy
pressure washer. It had not been run in at least 5 yrs..so they
declared it surplus and loaded it into my trailer with a fork lift.
I had to replace the fuel lines (diesel/fuel oil burner) and putz with
the pressure switches, grease the pump etc etc etc. One wheel was a
cripple, so used the pair I got at the last show in Visalia (perfect
size..$5 for the pair)
Works pretty good. However...I think its running too rich. Now this
may be due to a worn orfice, or the fuel/air mixture is not right. Air
mixture apparently is changed by opening/closing a vented band that
goes around the air intake side of the motor/blower housing. If I open
it too much..I get white smoke and not much heat. If I close it too
much..I get a faint black smoke and not a lot of heat.
There is no online manual on the Hotsy website. Anyone know of the
proper way to set fuel air mixture on a #2 fuel oil blower/igniter
gizmo? Or what I should be looking for as far as the exhaust output
is concerned? Do I need to buy a new nozzle? (I dont think Ive got a
drill bit that small anymore) I think...think there is too much fuel
going out the nozzle as the water tubes in the boiler are now pretty
blackened with soot (after filling the tank with a 5 gallon can here
marked Diesel..but had way way too much oil in it...had to dump it and
go buy some fresh..which did cause it to burn ..the first stuff
wouldnt even catch fire..and covered the tubes with oil..which smoked
a bit as it burned off.
Anyone know what the orfice size should be? I can solder it
shut..then redrill maybe.
I figure this is about the same sort of burner as a residential oil
burner..so...
Thanks
Gunner, now able to clean nasty oily machine tools squeeky clean
"A prudent man foresees the difficulties ahead and prepares for them;
the simpleton goes blindly on and suffers the consequences."
- Proverbs 22:3
|
|
Posted by Grant Erwin on March 20, 2006, 12:58 am
Please log in for more thread options
Can't answer your orifice question in any serious way (lots of off-color humor
comes to mind) but I commend you on your find. A hot steamer will indeed be
useful around your place. I have used hot water under pressure to take off grime
from surprising places. You can also use it to make money removing graffiti
should you choose to, don't know how much tagging goes on in Taft ..
GWE
Gunner wrote:
> One of the things I brought home this weekend..was a Mod 530 Hotsy
> pressure washer. It had not been run in at least 5 yrs..so they
> declared it surplus and loaded it into my trailer with a fork lift.
>
> I had to replace the fuel lines (diesel/fuel oil burner) and putz with
> the pressure switches, grease the pump etc etc etc. One wheel was a
> cripple, so used the pair I got at the last show in Visalia (perfect
> size..$5 for the pair)
>
> Works pretty good. However...I think its running too rich. Now this
> may be due to a worn orfice, or the fuel/air mixture is not right. Air
> mixture apparently is changed by opening/closing a vented band that
> goes around the air intake side of the motor/blower housing. If I open
> it too much..I get white smoke and not much heat. If I close it too
> much..I get a faint black smoke and not a lot of heat.
>
> There is no online manual on the Hotsy website. Anyone know of the
> proper way to set fuel air mixture on a #2 fuel oil blower/igniter
> gizmo? Or what I should be looking for as far as the exhaust output
> is concerned? Do I need to buy a new nozzle? (I dont think Ive got a
> drill bit that small anymore) I think...think there is too much fuel
> going out the nozzle as the water tubes in the boiler are now pretty
> blackened with soot (after filling the tank with a 5 gallon can here
> marked Diesel..but had way way too much oil in it...had to dump it and
> go buy some fresh..which did cause it to burn ..the first stuff
> wouldnt even catch fire..and covered the tubes with oil..which smoked
> a bit as it burned off.
>
> Anyone know what the orfice size should be? I can solder it
> shut..then redrill maybe.
>
> I figure this is about the same sort of burner as a residential oil
> burner..so...
>
> Thanks
>
> Gunner, now able to clean nasty oily machine tools squeeky clean
>
>
>
> "A prudent man foresees the difficulties ahead and prepares for them;
> the simpleton goes blindly on and suffers the consequences."
> - Proverbs 22:3
|
|
Posted by JR North on March 20, 2006, 7:26 pm
Please log in for more thread options Can't answer your orifice question either (I saw a girl standing on a
corner that might...)
Beware the pressure side-an old machine may be weak and have corrosion
or fatigue damage...don't want to hot-wash your face...
A fuel oil burner has a VERY narrow A/F range, and atomization,
turbulence, temperature of the combustion chamber, and the character of
the blower air flow all affect combustion. Make sure the blower wheel
and passages are clean, run fresh diesel through it, and tweak the mix
in tiny increments. You can pick up an HF laser temp guage(should have
one anyway...) for $50. Good for getting the hottest flame.
JR
Dweller in the cellar
Gunner wrote:
> One of the things I brought home this weekend..was a Mod 530 Hotsy
> pressure washer. It had not been run in at least 5 yrs..so they
> declared it surplus and loaded it into my trailer with a fork lift.
>
> I had to replace the fuel lines (diesel/fuel oil burner) and putz with
> the pressure switches, grease the pump etc etc etc. One wheel was a
> cripple, so used the pair I got at the last show in Visalia (perfect
> size..$5 for the pair)
>
> Works pretty good. However...I think its running too rich. Now this
> may be due to a worn orfice, or the fuel/air mixture is not right. Air
> mixture apparently is changed by opening/closing a vented band that
> goes around the air intake side of the motor/blower housing. If I open
> it too much..I get white smoke and not much heat. If I close it too
> much..I get a faint black smoke and not a lot of heat.
>
> There is no online manual on the Hotsy website. Anyone know of the
> proper way to set fuel air mixture on a #2 fuel oil blower/igniter
> gizmo? Or what I should be looking for as far as the exhaust output
> is concerned? Do I need to buy a new nozzle? (I dont think Ive got a
> drill bit that small anymore) I think...think there is too much fuel
> going out the nozzle as the water tubes in the boiler are now pretty
> blackened with soot (after filling the tank with a 5 gallon can here
> marked Diesel..but had way way too much oil in it...had to dump it and
> go buy some fresh..which did cause it to burn ..the first stuff
> wouldnt even catch fire..and covered the tubes with oil..which smoked
> a bit as it burned off.
>
> Anyone know what the orfice size should be? I can solder it
> shut..then redrill maybe.
>
> I figure this is about the same sort of burner as a residential oil
> burner..so...
>
> Thanks
>
> Gunner, now able to clean nasty oily machine tools squeeky clean
>
>
>
> "A prudent man foresees the difficulties ahead and prepares for them;
> the simpleton goes blindly on and suffers the consequences."
> - Proverbs 22:3
--
--------------------------------------------------------------
Home Page: http://www.seanet.com/~jasonrnorth
If you're not the lead dog, the view never changes
Doubt yourself, and the real world will eat you alive
The world doesn't revolve around you, it revolves around me
No skeletons in the closet; just decomposing corpses
--------------------------------------------------------------
Dependence is Vulnerability:
--------------------------------------------------------------
"Open the Pod Bay Doors please, Hal"
"I'm sorry, Dave, I'm afraid I can't do that.."
|
|
Posted by Tony on March 20, 2006, 7:32 pm
Please log in for more thread options You will need to replace the nozzle with a new one, available at any oil
burner supply, or from Hotsy. You can't just drill it out, anymore than you
could drill out a fuel injector, it is not a simple hole (complex fluid
dynamics). There are various atomizing spray patterns, (semi solid, hollow,
or solid), and the proper GPH rating. You must also set the pump pressure
to 100psi, adjust the air band setting, and check for proper ignition (Set
electrodes).
Tony
> One of the things I brought home this weekend..was a Mod 530 Hotsy
> pressure washer. It had not been run in at least 5 yrs..so they
> declared it surplus and loaded it into my trailer with a fork lift.
>
> I had to replace the fuel lines (diesel/fuel oil burner) and putz with
> the pressure switches, grease the pump etc etc etc. One wheel was a
> cripple, so used the pair I got at the last show in Visalia (perfect
> size..$5 for the pair)
>
> Works pretty good. However...I think its running too rich. Now this
> may be due to a worn orfice, or the fuel/air mixture is not right. Air
> mixture apparently is changed by opening/closing a vented band that
> goes around the air intake side of the motor/blower housing. If I open
> it too much..I get white smoke and not much heat. If I close it too
> much..I get a faint black smoke and not a lot of heat.
>
> There is no online manual on the Hotsy website. Anyone know of the
> proper way to set fuel air mixture on a #2 fuel oil blower/igniter
> gizmo? Or what I should be looking for as far as the exhaust output
> is concerned? Do I need to buy a new nozzle? (I dont think Ive got a
> drill bit that small anymore) I think...think there is too much fuel
> going out the nozzle as the water tubes in the boiler are now pretty
> blackened with soot (after filling the tank with a 5 gallon can here
> marked Diesel..but had way way too much oil in it...had to dump it and
> go buy some fresh..which did cause it to burn ..the first stuff
> wouldnt even catch fire..and covered the tubes with oil..which smoked
> a bit as it burned off.
>
> Anyone know what the orfice size should be? I can solder it
> shut..then redrill maybe.
>
> I figure this is about the same sort of burner as a residential oil
> burner..so...
>
> Thanks
>
> Gunner, now able to clean nasty oily machine tools squeeky clean
>
>
>
> "A prudent man foresees the difficulties ahead and prepares for them;
> the simpleton goes blindly on and suffers the consequences."
> - Proverbs 22:3
|
|
Posted by Gunner on March 21, 2006, 12:12 am
Please log in for more thread options wrote:
>You will need to replace the nozzle with a new one, available at any oil
>burner supply, or from Hotsy. You can't just drill it out, anymore than you
>could drill out a fuel injector, it is not a simple hole (complex fluid
>dynamics). There are various atomizing spray patterns, (semi solid, hollow,
>or solid), and the proper GPH rating. You must also set the pump pressure
>to 100psi, adjust the air band setting, and check for proper ignition (Set
>electrodes).
>
>Tony
Cool. Now how do I adjust the fuel pump pressure? Its an outboard pump
mounted to the end of the blower motor, with no obvious adjustments.
Just a "brake" style bleeder, a drain, a gauge port and a second
return port, all plugged off.
Ajusted the air band for the best setting possible, but its still too
rich
Ignition was adjusted perfectly according to the diagram on the
ignitor cover.
Ill do a web search and see if there is a Hotsy dealer in So. Cal I
can stop in.
Gunner
>
>> One of the things I brought home this weekend..was a Mod 530 Hotsy
>> pressure washer. It had not been run in at least 5 yrs..so they
>> declared it surplus and loaded it into my trailer with a fork lift.
>>
>> I had to replace the fuel lines (diesel/fuel oil burner) and putz with
>> the pressure switches, grease the pump etc etc etc. One wheel was a
>> cripple, so used the pair I got at the last show in Visalia (perfect
>> size..$5 for the pair)
>>
>> Works pretty good. However...I think its running too rich. Now this
>> may be due to a worn orfice, or the fuel/air mixture is not right. Air
>> mixture apparently is changed by opening/closing a vented band that
>> goes around the air intake side of the motor/blower housing. If I open
>> it too much..I get white smoke and not much heat. If I close it too
>> much..I get a faint black smoke and not a lot of heat.
>>
>> There is no online manual on the Hotsy website. Anyone know of the
>> proper way to set fuel air mixture on a #2 fuel oil blower/igniter
>> gizmo? Or what I should be looking for as far as the exhaust output
>> is concerned? Do I need to buy a new nozzle? (I dont think Ive got a
>> drill bit that small anymore) I think...think there is too much fuel
>> going out the nozzle as the water tubes in the boiler are now pretty
>> blackened with soot (after filling the tank with a 5 gallon can here
>> marked Diesel..but had way way too much oil in it...had to dump it and
>> go buy some fresh..which did cause it to burn ..the first stuff
>> wouldnt even catch fire..and covered the tubes with oil..which smoked
>> a bit as it burned off.
>>
>> Anyone know what the orfice size should be? I can solder it
>> shut..then redrill maybe.
>>
>> I figure this is about the same sort of burner as a residential oil
>> burner..so...
>>
>> Thanks
>>
>> Gunner, now able to clean nasty oily machine tools squeeky clean
>>
>>
>>
>> "A prudent man foresees the difficulties ahead and prepares for them;
>> the simpleton goes blindly on and suffers the consequences."
>> - Proverbs 22:3
>
"A prudent man foresees the difficulties ahead and prepares for them;
the simpleton goes blindly on and suffers the consequences."
- Proverbs 22:3
|
| Similar Threads | Posted | | fit up pressure washer hose | February 21, 2008, 6:51 am |
| OT: Please help Pressure washer injector problem.. | January 14, 2007, 6:28 pm |
| OT: Pressure washer winter storage | September 9, 2007, 8:12 pm |
| not really totally OT --- Johnny Cash and why I want a new pressure washer - help me out here | October 2, 2006, 1:51 am |
| Dryer or Frontloading Washer as Makeshift Tumbler/Parts Washer? | October 21, 2006, 10:44 pm |
| Re: Getting An Enclosed Trailer...Questions, Questions, Questions | December 21, 2007, 12:06 am |
| Pressurized parts washer | July 23, 2006, 3:01 pm |
| Scrounging Washer Motor | October 18, 2006, 11:54 am |
| Dishwasher as a parts washer | November 14, 2006, 5:12 pm |
| Power Washer Problems? | February 10, 2007, 7:50 pm |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap
> pressure washer. It had not been run in at least 5 yrs..so they
> declared it surplus and loaded it into my trailer with a fork lift.
>
> I had to replace the fuel lines (diesel/fuel oil burner) and putz with
> the pressure switches, grease the pump etc etc etc. One wheel was a
> cripple, so used the pair I got at the last show in Visalia (perfect
> size..$5 for the pair)
>
> Works pretty good. However...I think its running too rich. Now this
> may be due to a worn orfice, or the fuel/air mixture is not right. Air
> mixture apparently is changed by opening/closing a vented band that
> goes around the air intake side of the motor/blower housing. If I open
> it too much..I get white smoke and not much heat. If I close it too
> much..I get a faint black smoke and not a lot of heat.
>
> There is no online manual on the Hotsy website. Anyone know of the
> proper way to set fuel air mixture on a #2 fuel oil blower/igniter
> gizmo? Or what I should be looking for as far as the exhaust output
> is concerned? Do I need to buy a new nozzle? (I dont think Ive got a
> drill bit that small anymore) I think...think there is too much fuel
> going out the nozzle as the water tubes in the boiler are now pretty
> blackened with soot (after filling the tank with a 5 gallon can here
> marked Diesel..but had way way too much oil in it...had to dump it and
> go buy some fresh..which did cause it to burn ..the first stuff
> wouldnt even catch fire..and covered the tubes with oil..which smoked
> a bit as it burned off.
>
> Anyone know what the orfice size should be? I can solder it
> shut..then redrill maybe.
>
> I figure this is about the same sort of burner as a residential oil
> burner..so...
>
> Thanks
>
> Gunner, now able to clean nasty oily machine tools squeeky clean
>
>
>
> "A prudent man foresees the difficulties ahead and prepares for them;
> the simpleton goes blindly on and suffers the consequences."
> - Proverbs 22:3