|
Posted by Ignoramus13075 on July 13, 2008, 6:58 pm
Please log in for more thread options
I finally understood what was wrong. My own reconstruction of what
happened at some point prior to my lathe purchase, is as follows: the
missing spring holding the lower bar (see picture) broke or was
lost. Because of this, the lathe would not turn on. Then the dumbass
who was fixing the lathe tried to rewire the starter. To no
avail. Then he or she inserted red plastic blocks into the size 0
starter, therefore fixing it mechanically to be always on.
When I realized the nature of these red plastic blocks, the fix was
obvious: remove then, rewire the starter for a single non-momentary
switch, and use a spring to fix the original mechanical problem. I was
very lucky, because I had a nice coil spring assortment (pictured).
So, as of now, the problem is fully resolved and the ON/OFF/BRAKE
switch works great!
More pix at
http://igor.chudov.com/projects/Clausing-Colchester-13-36-Master-Lathe/08-On-Off-Switch/
--
Due to extreme spam originating from Google Groups, and their inattention
to spammers, I and many others block all articles originating
from Google Groups. If you want your postings to be seen by
more readers you will need to find a different means of
posting on Usenet.
http://improve-usenet.org/
|
|
Posted by William Noble on July 14, 2008, 12:13 am
Please log in for more thread options
>I finally understood what was wrong. My own reconstruction of what
> happened at some point prior to my lathe purchase, is as follows: the
> missing spring holding the lower bar (see picture) broke or was
> lost. Because of this, the lathe would not turn on. Then the dumbass
> who was fixing the lathe tried to rewire the starter. To no
> avail. Then he or she inserted red plastic blocks into the size 0
> starter, therefore fixing it mechanically to be always on.
>
>
> When I realized the nature of these red plastic blocks, the fix was
> obvious: remove then, rewire the starter for a single non-momentary
> switch, and use a spring to fix the original mechanical problem. I was
> very lucky, because I had a nice coil spring assortment (pictured).
>
> So, as of now, the problem is fully resolved and the ON/OFF/BRAKE
> switch works great!
>
you know, it's really amazing how many things I've picked up over the years
that were fine after some simple repair which some prior idiot had been
unable to perform, typically because the prior repair was made by somebody
with no understanding of the mechanism
** Posted from http://www.teranews.com **
|
|
Posted by Ignoramus13075 on July 14, 2008, 12:50 am
Please log in for more thread options >
>>I finally understood what was wrong. My own reconstruction of what
>> happened at some point prior to my lathe purchase, is as follows: the
>> missing spring holding the lower bar (see picture) broke or was
>> lost. Because of this, the lathe would not turn on. Then the dumbass
>> who was fixing the lathe tried to rewire the starter. To no
>> avail. Then he or she inserted red plastic blocks into the size 0
>> starter, therefore fixing it mechanically to be always on.
>>
>>
>> When I realized the nature of these red plastic blocks, the fix was
>> obvious: remove then, rewire the starter for a single non-momentary
>> switch, and use a spring to fix the original mechanical problem. I was
>> very lucky, because I had a nice coil spring assortment (pictured).
>>
>> So, as of now, the problem is fully resolved and the ON/OFF/BRAKE
>> switch works great!
>>
>
>
> you know, it's really amazing how many things I've picked up over the years
> that were fine after some simple repair which some prior idiot had been
> unable to perform, typically because the prior repair was made by somebody
> with no understanding of the mechanism
>
Indeedy. Gives some feeling of satisfaction.
However, I recall a number of things that I fscked up, due to the
exact above reason, but fortunately I can count them on the fingers of
my one hand.
--
Due to extreme spam originating from Google Groups, and their inattention
to spammers, I and many others block all articles originating
from Google Groups. If you want your postings to be seen by
more readers you will need to find a different means of
posting on Usenet.
http://improve-usenet.org/
|
|
Posted by Bruce L. Bergman on July 15, 2008, 11:34 am
Please log in for more thread options On Sun, 13 Jul 2008 23:50:09 -0500, Ignoramus13075
>Indeedy. Gives some feeling of satisfaction.
>
>However, I recall a number of things that I fscked up, due to the
>exact above reason, but fortunately I can count them on the fingers of
>my one hand.
You worded that rather strangely, where an inference can be made -
And what happened to the other hand?
Most people come equipped with two hands from the factory, each with
a complement of four fingers and one opposing thumb each - Was that
one of the fsckups?
--<< Bruce >>--
|
|
Posted by Ignoramus19502 on July 15, 2008, 11:38 am
Please log in for more thread options > On Sun, 13 Jul 2008 23:50:09 -0500, Ignoramus13075
>
>
>>Indeedy. Gives some feeling of satisfaction.
>>
>>However, I recall a number of things that I fscked up, due to the
>>exact above reason, but fortunately I can count them on the fingers of
>>my one hand.
>
> You worded that rather strangely, where an inference can be made -
> And what happened to the other hand?
>
> Most people come equipped with two hands from the factory, each with
> a complement of four fingers and one opposing thumb each - Was that
> one of the fsckups?
>
>
I would use the second hand to count the fingers on the first hand
--
Due to extreme spam originating from Google Groups, and their inattention
to spammers, I and many others block all articles originating
from Google Groups. If you want your postings to be seen by
more readers you will need to find a different means of
posting on Usenet.
http://improve-usenet.org/
|
| Similar Threads | Posted | | I'd rather fight than switch! (changing speeds on belt driven lathe) | August 6, 2007, 11:11 am |
| High speed Spindle...solved! | October 20, 2006, 12:27 am |
| Water Hammering solved--with some aplumb, btw... | April 2, 2007, 5:18 pm |
| Re: Clausing 5914 chatter -- solved at last | April 5, 2008, 7:55 pm |
| Re: Clausing 5914 chatter -- solved at last | April 5, 2008, 10:26 pm |
| Re: Clausing 5914 chatter -- solved at last | April 6, 2008, 3:18 am |
| Re: Clausing 5914 chatter -- solved at last | April 6, 2008, 3:04 pm |
| Re: Clausing 5914 chatter -- solved at last | April 6, 2008, 5:48 pm |
| Re: Clausing 5914 chatter -- solved at last | April 7, 2008, 12:50 am |
| Re: Clausing 5914 chatter -- solved at last | April 7, 2008, 10:10 pm |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap
> happened at some point prior to my lathe purchase, is as follows: the
> missing spring holding the lower bar (see picture) broke or was
> lost. Because of this, the lathe would not turn on. Then the dumbass
> who was fixing the lathe tried to rewire the starter. To no
> avail. Then he or she inserted red plastic blocks into the size 0
> starter, therefore fixing it mechanically to be always on.
>
>
> When I realized the nature of these red plastic blocks, the fix was
> obvious: remove then, rewire the starter for a single non-momentary
> switch, and use a spring to fix the original mechanical problem. I was
> very lucky, because I had a nice coil spring assortment (pictured).
>
> So, as of now, the problem is fully resolved and the ON/OFF/BRAKE
> switch works great!
>