|
Posted by Karl Townsend on May 5, 2008, 9:37 pm
Please log in for more thread options
I've been on the search for a Lagun ftv-4..
There's TWO at an auction in Denver. Bit of a road trip. I'd gladly pay
somebody to go inspect it, take a bunch of pics, and talk to me over the
phone while you're in front of it.
Karl
|
|
Posted by RoyJ on May 5, 2008, 10:56 pm
Please log in for more thread options
Sheesh, you are complaining about 870 miles each way for a quickie road
trip? At $3.50 a gallon for gas?
Karl Townsend wrote:
> I've been on the search for a Lagun ftv-4..
>
> There's TWO at an auction in Denver. Bit of a road trip. I'd gladly pay
> somebody to go inspect it, take a bunch of pics, and talk to me over the
> phone while you're in front of it.
> Karl
>
>
|
|
Posted by Gunner Asch on May 6, 2008, 1:06 am
Please log in for more thread options On Mon, 5 May 2008 20:37:56 -0500, "Karl Townsend"
>I've been on the search for a Lagun ftv-4..
>
>There's TWO at an auction in Denver. Bit of a road trip. I'd gladly pay
>somebody to go inspect it, take a bunch of pics, and talk to me over the
>phone while you're in front of it.
>Karl
>
I think I know of one in California..Anaheim
Even more of a road trip.
http://www.mcleanlathe.com/
Ask for Joe or Mike, tell him Gunner the OmniTurn guy referred you.
Thats a BIG freaking mill. Even I nearly need a stepladder to run it.
Gunner
Political Correctness is a doctrine fostered by a delusional,
illogical liberal minority, and rabidly promoted by an
unscrupulous mainstream media, which holds forth the
proposition that it is entirely possible to pick up a turd by the clean end.
|
|
Posted by Karl Townsend on May 6, 2008, 6:50 am
Please log in for more thread options
> I think I know of one in California..Anaheim
>
> Even more of a road trip.
>
> http://www.mcleanlathe.com/
>
> Ask for Joe or Mike, tell him Gunner the OmniTurn guy referred you.
>
> Thats a BIG freaking mill. Even I nearly need a stepladder to run it.
You should see one make chips. Do you know, for sure, of the condition of
this unit? There's an FTV-4 on eBay, reliable tool, right now. looks like
they did a super job cleaning a beater. I almost contacted you for an
inspection of that unit.
I shook hands with a fella to buy my Bridgeport just as soon as I get a
replacement mill. Plus, my son is laid off right now. I'm buying gas to
anywhere in the good old US of A to pick up a nice FTV-4.
Karl
|
|
Posted by Gunner Asch on May 6, 2008, 1:39 pm
Please log in for more thread options On Tue, 6 May 2008 05:50:38 -0500, "Karl Townsend"
>
>> I think I know of one in California..Anaheim
>>
>> Even more of a road trip.
>>
>> http://www.mcleanlathe.com/
>>
>> Ask for Joe or Mike, tell him Gunner the OmniTurn guy referred you.
>>
>> Thats a BIG freaking mill. Even I nearly need a stepladder to run it.
>
>You should see one make chips. Do you know, for sure, of the condition of
>this unit? There's an FTV-4 on eBay, reliable tool, right now. looks like
>they did a super job cleaning a beater. I almost contacted you for an
>inspection of that unit.
>
>I shook hands with a fella to buy my Bridgeport just as soon as I get a
>replacement mill. Plus, my son is laid off right now. I'm buying gas to
>anywhere in the good old US of A to pick up a nice FTV-4.
>
>Karl
>
Im not sure, for sure, but it was under power when I was in there
last. No one wanted to use it, because they are all short latinos, and
needed to stand on a box to run it.
Give em a call and see what they say
Gunner
Political Correctness is a doctrine fostered by a delusional,
illogical liberal minority, and rabidly promoted by an
unscrupulous mainstream media, which holds forth the
proposition that it is entirely possible to pick up a turd by the clean end.
|
| Similar Threads | Posted | | Alabaster imparts works with special glow (Denver Post) | May 13, 2007, 11:05 am |
| Quality Assurance Inspection Software | December 8, 2006, 7:40 pm |
| Ballpark of the weight of a milling machine head and how to separate the head form the machine safely | June 19, 2007, 5:43 pm |
| Anyone want to buy this machine? Or at least help me with it. | May 2, 2006, 9:56 pm |
| Anyone see this machine? | February 12, 2008, 6:57 am |
| Best Cut-off Machine | August 6, 2008, 11:31 am |
| Cry with me...machine damage! | July 8, 2006, 8:55 pm |
| Burgmaster 0B - anyone know this machine? | July 12, 2006, 12:00 am |
| how to do these w/o machine shop (or even with, for some)? | August 6, 2006, 9:31 am |
| Machine auction | September 9, 2006, 11:56 pm |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap
>
> There's TWO at an auction in Denver. Bit of a road trip. I'd gladly pay
> somebody to go inspect it, take a bunch of pics, and talk to me over the
> phone while you're in front of it.
> Karl
>
>