|
General Metalworking - All aspects of working with metal.
|
|
|
|
|
Posted by William Noble on February 3, 2008, 11:04 pm
Please log in for more thread options
just picked up a "nicer" drill press to replace my Taiwan clone that has
served me all these years - but my "new" drill press has a damaged gear in
the lift assembly for the table - there is a parts list here:
http://www.mikestools.com/Delta-Drill-Press-Parts-Lists_2282.aspx
what I need is item 111 on the diagram, which it calls "compound gear"
and I notice that itmes 21-24, 67-69 are also missing (same parts as raise
the table) - I presume these allow the head to be raised and lowered?
anyone know what they are for? if it is to raise/lower the head, then that
is cool, but I'd need another rack (item 124) also.
So, someone must have a dead one of these with a damaged casting or
something that can be a source of parts/?? I can make the gear, but I
think I'd rather not.
anyone?
--
bill
to email me, to to my web page, www.wbnoble.com and find my email
--
Posted via a free Usenet account from http://www.teranews.com
|
|
Posted by Ned Simmons on February 4, 2008, 6:31 pm
Please log in for more thread options
On Sun, 3 Feb 2008 20:04:35 -0800, "William Noble"
>just picked up a "nicer" drill press to replace my Taiwan clone that has
>served me all these years - but my "new" drill press has a damaged gear in
>the lift assembly for the table - there is a parts list here:
>http://www.mikestools.com/Delta-Drill-Press-Parts-Lists_2282.aspx
I can't help you with the gear, but will tell you that it's worth
fixing. I had one of those with the power feed and oil trough table -
it was one of the nicest drill presses I've ever used.
--
Ned Simmons
|
|
Posted by William Noble on February 4, 2008, 11:33 pm
Please log in for more thread options
> On Sun, 3 Feb 2008 20:04:35 -0800, "William Noble"
>
>>just picked up a "nicer" drill press to replace my Taiwan clone that has
>>served me all these years - but my "new" drill press has a damaged gear in
>>the lift assembly for the table - there is a parts list here:
>>http://www.mikestools.com/Delta-Drill-Press-Parts-Lists_2282.aspx
>
> I can't help you with the gear, but will tell you that it's worth
> fixing. I had one of those with the power feed and oil trough table -
> it was one of the nicest drill presses I've ever used.
>
> --
> Ned Simmons
Ned, or anyone else, if you have a user's manual or brochure for these, I
would sure like to see a copy or a scan - it is really not obvious why there
should be that second crank handle, and maybe a manual would make
everything clear .... or maybe not -
How did the power feed work? I have found a picture of one with a foot
pedal, I understand that, but I haven't found anything that looks like a
power feed.
And, I'm debating putting a VFD on it versus switching to a single phase
motor, versus adding a capacitor and relay to start the 3 phase motor. if I
can find a used/surplus VFD for a cheap price, I think I'll go that way -
3/4 hp
--
Posted via a free Usenet account from http://www.teranews.com
|
|
Posted by Ned Simmons on February 5, 2008, 11:44 am
Please log in for more thread options On Mon, 4 Feb 2008 20:33:58 -0800, "William Noble"
-
>
>How did the power feed work? I have found a picture of one with a foot
>pedal, I understand that, but I haven't found anything that looks like a
>power feed.
>
There was a gearbox on the right hand side of the head, inboard of the
downfeed handle, thru which the downfeed shaft passed. The motor had a
double shaft; small cone pulleys between the motor's bottom shaft and
the feed box drove the feed and allowed for feed changes. As I recall,
the feed was engaged much like the old drill presses where you lift a
worm to mesh with a wormwheel on the downfeed shaft.
--
Ned Simmons
|
| Similar Threads | Posted | | Parts Needed for old Delta/Rockwell Drill Press 15-655 | September 29, 2006, 12:23 pm |
| anyone need old Delta 17 inch drill presses or parts? | February 27, 2008, 1:16 am |
| Anyone Have a Delta 17-965 Drill Press | April 27, 2006, 3:21 pm |
| delta drill press table | September 15, 2008, 3:05 pm |
| parts for Atlas drill press?? | September 26, 2007, 8:27 pm |
| WTB Delta 17 drill press high speed spindle pulley and spindle. | May 28, 2007, 1:26 am |
| arboga maskiner drill press parts | June 19, 2007, 11:26 am |
| Delta Drill / Farm & Fleet | December 5, 2006, 11:37 am |
| How can I automatically tap 500 holes in 5/16-18 thread size using a hand drill or drill press? | January 1, 2008, 6:18 pm |
| Sellers 1G drill Grinder parts? | May 19, 2008, 1:07 pm |
|
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap
>served me all these years - but my "new" drill press has a damaged gear in
>the lift assembly for the table - there is a parts list here:
>http://www.mikestools.com/Delta-Drill-Press-Parts-Lists_2282.aspx