|
Posted by gn3dr on October 6, 2006, 8:03 am
Please log in for more thread options
lemel_man Wrote:
> My mill (Centec 2B) also has 30NT taper, and also came with
an Autolock
> chuck and collets. I found, as you have, that not all my cutters
> fitted,
> especially those with no threads. I splashed out and bought an ER32
> system; chuck and full set of collets. I use it all the time; its far
> more versatile than the Autolock.
>
> --
> Regards, Gary Wooding
> ]
Gary (or anyone else who knows)
Where did you get the INT 30 ER32 collet system. Been having a quick
look on the
web but this particular combination doesn't seem to be
listed in a lot of
places. I am probably also getting a bit confused
between att the different
standards e.g. is 30INt the same as ISO30.
--
gn3dr
------------------------------------------------------------------------
gn3dr's
Profile: http://www.rcgroups.com/forums/member.php?u=80271
View this thread:
http://www.rcgroups.com/forums/showthread.php?t=577998
|
|
Posted by Tim Leech on October 6, 2006, 9:23 am
Please log in for more thread options
wrote:
>
>lemel_man Wrote:
>> My mill (Centec 2B) also has 30NT taper, and also came with an Autolock
>> chuck and collets. I found, as you have, that not all my cutters
>> fitted,
>> especially those with no threads. I splashed out and bought an ER32
>> system; chuck and full set of collets. I use it all the time; its far
>> more versatile than the Autolock.
>>
>> --
>> Regards, Gary Wooding
>> ]
>
>Gary (or anyone else who knows)
>Where did you get the INT 30 ER32 collet system. Been having a quick
>look on the web but this particular combination doesn't seem to be
>listed in a lot of places. I am probably also getting a bit confused
>between att the different standards e.g. is 30INt the same as ISO30.
I got mine, Bison/Toolmex brand, from my local tool shop when they had
an offer on in their flyer.
ISO 30 is a particular form of 30INT; subject to drawbar thead, all
ISO30 should fit 30int spindles.
Cheers
Tim
Dutton Dry-Dock
Traditional & Modern canal craft repairs
Vintage diesel engine service
|
|
Posted by lemel_man on October 6, 2006, 9:40 am
Please log in for more thread options gn3dr wrote:
> lemel_man Wrote:
>> My mill (Centec 2B) also has 30NT taper, and also came with an Autolock
>> chuck and collets. I found, as you have, that not all my cutters
>> fitted,
>> especially those with no threads. I splashed out and bought an ER32
>> system; chuck and full set of collets. I use it all the time; its far
>> more versatile than the Autolock.
>>
>> --
>> Regards, Gary Wooding
>> ]
>
> Gary (or anyone else who knows)
> Where did you get the INT 30 ER32 collet system. Been having a quick
> look on the web but this particular combination doesn't seem to be
> listed in a lot of places. I am probably also getting a bit confused
> between att the different standards e.g. is 30INt the same as ISO30.
>
>
I got mine from RDG Tools in Hebden Bridge, its made by Vertex. If
you're going to the Midlands Exhibition at the Fosse this year, I'm sure
they'll be there - they were last year.
INT30 is essentially the same as ISO30, but the drawbar threads are
different, I believe.
--
Regards, Gary Wooding
(To reply by email, change feet to foot in my address)
--
Posted via a free Usenet account from http://www.teranews.com
|
|
Posted by Tim Leech on October 6, 2006, 10:12 am
Please log in for more thread options wrote:
>gn3dr wrote:
>INT30 is essentially the same as ISO30, but the drawbar threads are
>different, I believe.
>
I believe there are other small differences which don't matter for
most purposes. ISO30 *always* has, AFAIK, M12 drawbar thread; 30 int
can be seen with all manner of threads.
Cheers
Tim
Dutton Dry-Dock
Traditional & Modern canal craft repairs
Vintage diesel engine service
|
| Similar Threads | Posted | | Miniature S Type Autolock | September 12, 2006, 1:54 pm |
| Re: Clarkson Autolock | September 10, 2006, 5:39 pm |
| Clarkson Autolock | September 10, 2006, 4:56 pm |
| Free F type collets | November 13, 2008, 10:02 am |
| Clarkson collet needed | February 23, 2008, 12:43 pm |
| Clarkson MkI Cutter Grinder | April 28, 2008, 4:24 am |
| Selling: Clarkson 1/12th scale Sanderson Beam Engine | October 10, 2008, 5:56 am |
| Re: ER collets | September 13, 2006, 11:55 am |
| ER collets | August 17, 2006, 5:18 am |
| Re: ER collets | August 21, 2006, 11:55 am |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap