|
Posted by SteveB on April 16, 2008, 12:15 pm
Please log in for more thread options
I'm setting up my tools now on a welding trailer. I'll probably buy a
Knaack box or similar, depending on what I can find to fit the space
available.
For rods, I used to use plastic cylinders that had a screw top, an O-ring in
the middle, and a piece of foam in the bottom. I did not have any problem
with rods losing their coatings due to bouncing around. Do you find this to
be much of a problem?
I liked the tubes, as they were easy to label, and easy to stack and store.
Is there a better way to store multiple rod types, keep them dry, and keep
them from rattling the coatings off during highway travel? One central box
with dividers may be better than several smaller ones. But then, it was
nice to just take the whole tube to the welding and not carry a pocket full
that could become damaged or contaminated.
Steve
|
|
Posted by Ignoramus12441 on April 16, 2008, 12:47 pm
Please log in for more thread options
I am a very happy user of these tubes for 6013. For 7018 I use an
oven. I think that realistically, if the tubes themselves are not
moving, bouncing around should not be a big issue.
i
|
|
Posted by Grant Erwin on April 16, 2008, 2:01 pm
Please log in for more thread options SteveB wrote:
> I'm setting up my tools now on a welding trailer. I'll probably buy a
> Knaack box or similar, depending on what I can find to fit the space
> available.
>
> For rods, I used to use plastic cylinders that had a screw top, an O-ring in
> the middle, and a piece of foam in the bottom. I did not have any problem
> with rods losing their coatings due to bouncing around. Do you find this to
> be much of a problem?
>
> I liked the tubes, as they were easy to label, and easy to stack and store.
> Is there a better way to store multiple rod types, keep them dry, and keep
> them from rattling the coatings off during highway travel? One central box
> with dividers may be better than several smaller ones. But then, it was
> nice to just take the whole tube to the welding and not carry a pocket full
> that could become damaged or contaminated.
>
> Steve
>
>
I have to figure you aren't going to pull your welder to a job without knowing
what the job looks like in detail; i.e. what kind of rod you will need. I
generally only use 6010 or 7018, and the latter I bring in sealed cans from
the welding supply store which get emptied directly into a jobsite Phoenix
rod oven. For 60XX sure, I'd put it in those rod keeper tubes. If you buy
a Rod Keeper brand setup, you can get 3 tubes and a weld-on (or bolt-on) hanger
onto which you can clip all 3 tubes securely. That might be a good way to go.
Grant
|
|
Posted by johnnytorch on April 16, 2008, 5:21 pm
Please log in for more thread options > I'm setting up my tools now on a welding trailer. I'll probably buy a
> Knaack box or similar, depending on what I can find to fit the space
> available.
>
> For rods, I used to use plastic cylinders that had a screw top, an O-ring
> in the middle, and a piece of foam in the bottom. I did not have any
> problem with rods losing their coatings due to bouncing around. Do you
> find this to be much of a problem?
>
> I liked the tubes, as they were easy to label, and easy to stack and
> store. Is there a better way to store multiple rod types, keep them dry,
> and keep them from rattling the coatings off during highway travel? One
> central box with dividers may be better than several smaller ones. But
> then, it was nice to just take the whole tube to the welding and not carry
> a pocket full that could become damaged or contaminated.
>
> Steve
Whatever method you choose, keep it full of rods. The empty space is what
will damage them by allowing them to bounce, shift, and smack into each
other.
|
| Similar Threads | Posted | | tank storage | December 16, 2007, 4:52 pm |
| Re: Large quantity rod storage? | February 15, 2008, 5:15 am |
| Re: Large quantity rod storage? | February 15, 2008, 7:44 am |
| Re: Large quantity rod storage? | February 15, 2008, 8:14 am |
| Re: Large quantity rod storage? | February 15, 2008, 1:13 pm |
| Re: Large quantity rod storage? | February 15, 2008, 7:08 pm |
| Re: Large quantity rod storage? | February 17, 2008, 6:10 pm |
| Re: Large quantity rod storage? | February 18, 2008, 6:37 pm |
| Re: Large quantity rod storage? | February 18, 2008, 8:14 pm |
| Re: Large quantity rod storage? | February 25, 2008, 10:41 pm |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap
> Knaack box or similar, depending on what I can find to fit the space
> available.
>
> For rods, I used to use plastic cylinders that had a screw top, an O-ring in
> the middle, and a piece of foam in the bottom. I did not have any problem
> with rods losing their coatings due to bouncing around. Do you find this to
> be much of a problem?
>
> I liked the tubes, as they were easy to label, and easy to stack and store.
> Is there a better way to store multiple rod types, keep them dry, and keep
> them from rattling the coatings off during highway travel? One central box
> with dividers may be better than several smaller ones. But then, it was
> nice to just take the whole tube to the welding and not carry a pocket full
> that could become damaged or contaminated.
>
> Steve
>
>