|
Posted by Kerry on May 5, 2007, 7:51 am
Please log in for more thread options
> Hey Folks,
>
> After my mom returned two different fire 'pit' patio tables to the
> store she bought them from, i signed my brother and i up to building
> her one. We're both rookies, but have been looking for a project like
> this to get started. We have a MIG welder, chop saw, grinders, etc.
>
> I was going to try to whip up a plan from scratch but wondered if any
> of you folks might know where i could find some to start from. I'd
> like to use either slate or thick tile for the table surface and have
> a square center for the pit (which will probably be the base from a
> cheap grill). I like the 'grid' look of 12" or 18" tile, but am not
> going to be picky at this point.
>
> Any pointers would be much appreciated!!!
>
> Thanks
>
Been thinking about the same sort of project myself. I was hoping to find a
200lb propane tank to use for the pit though. The gas companies can only
use them so long before they have to replace them so I was hoping to be in
the right spot at the right time. If I remove the fittings from the end, I
can fill it with water and let it stand for a few days. That should
displace any of the gas that may be left inside. From there cutting the
bottom 12" off should make a really nice bowl for the pit. I have also
thought that using a hole saw to cut say a 3 or 4" hole in the very center
would make a nice trap door to empty the ashes out through. A simple hinge
and a bit of flatstock could be used as a catch to hold it closed.
The firebowl should be easy enough to weld to a "table" top or simple
brackets and a few carriage bolts will hold it in place if the metal doesn't
like the arc. A bit of expanded metal can be fashioned into a cover to
catch embers though I would stick with a fairly small (1/4 to 3/8) opening
for that. Heck you could make a grill out of it too. (now I'm getting
hungry) A few shrimp, chicken legs or wings or sirloin tips over the hot
coals and a nice cold beverage...some good friends around you or that one
special lady... Damn I gotta build one of these now!
Anyhow other thoughts have been to use 1/4 inch thick boiler plate in a
pyramid shape. Again the very point would be cut off so a piece of plate
could be used as an ash door.
I'm leaning towards having the fire bowl sit about 1.5 inches high of the
metal table. The borders of the table would be angle iron in maybe an
octagonal shape with simple 1/2" rod legs bent in a "V" shape welded at the
outer corners and the center pit. Rebar would work but not as pretty
perhaps. For the camp fine. For the home patio cold rolled steel rod is
better. A few angle iron braces between the outer rim and the inside should
hold it together.
This is where I get unsure of what to do for the table top. I think I could
fill the space between the inner and outer rim with cardboard (temporary)
then mason's mesh for strength. Now use a motar mix (or should it be
thinset???) and fill in the tabletop. I would then press stones, slate,
tiles, (whatever she says would look nice) into the "cement" to form the
actual surface. Once hardened the cardboard could be peeled away. It was
only there to keep the motar from falling through the mesh. I suppose I
could use 18 or 20 guage sheetmetal instead and left it in place. Actually
that may be the way to go really.
As to sizing, I would think the fire bowl is where you start and the table
portion should be at least 15" from the pit to the edge. Just in case you
want to play cards or eat around it. This would mean 30' + the diameter of
the firepit. I would guess 48-50" or thereabouts.
What are your thoughts???
| 
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap
>
> After my mom returned two different fire 'pit' patio tables to the
> store she bought them from, i signed my brother and i up to building
> her one. We're both rookies, but have been looking for a project like
> this to get started. We have a MIG welder, chop saw, grinders, etc.
>
> I was going to try to whip up a plan from scratch but wondered if any
> of you folks might know where i could find some to start from. I'd
> like to use either slate or thick tile for the table surface and have
> a square center for the pit (which will probably be the base from a
> cheap grill). I like the 'grid' look of 12" or 18" tile, but am not
> going to be picky at this point.
>
> Any pointers would be much appreciated!!!
>
> Thanks
>